How To Change EPS Carry Reticle: Step-by-Step Holosun Adjustment Guide
Changing the reticle on a Holosun EPS Carry is managed through the onboard push-button interface by cycling through the multi-reticle system options of a 2 MOA dot, 32 MOA circle, or combined dot-and-circle configuration. Master this procedure to match your optic's display to environmental lighting conditions and personal astigmatism constraints without losing zero.
Pre-Operation & Equipment Checklist
Executing a reticle change on an enclosed micro reflex sight like the Holosun EPS Carry requires understanding the physical controls and power states of the optic housing. Because the EPS Carry utilizes a side-mounted battery tray and a top-deck solar fail-safe alongside manual adjustment buttons, you do not need any physical tools to alter the reticle display. However, verifying the operational state of the micro-electronic LED emitter is critical before making adjustments.
- Essential Gear and Tools: Holosun EPS Carry optic (mounted on firearm), lint-free micro-fiber lens cloth, optional torque wrench (T10 Torx) if confirming mount stability, and a clean workspace with adequate ambient lighting.
- Prerequisite Standards: Familiarity with the left-side housing button layout (marked with plus and minus symbols), understanding of parallax-free focal planes, and basic knowledge of battery voltage (CR1632 lithium cell) to prevent low-voltage emitter dimming.
- Time and Budget Benchmarks: Estimated duration is under two minutes. Cost is zero dollars, as this is a built-in firmware feature of the multi-reticle system (MRS).
Step-by-Step EPS Carry Reticle Modification Process
Step 1: Wake the Optic and Verify Power Status
Ensure the Holosun EPS Carry is powered on and actively projecting a reticle onto the aspheric glass lens. If the optic is in sleep mode due to the Shake Awake motion-sensing technology, gently shake the firearm or press either the plus or minus adjustment button once to activate the LED emitter. Confirm that the glass is free of debris, lint, or oil smudges that could distort the appearance of the multi-reticle options.
Warning: Never use chemical solvents, acetone, or abrasive paper towels to clean the objective lenses of your EPS Carry, as these substances strip the multi-layer anti-reflective optical coatings.
Step 2: Access the Reticle Selection Programming Mode
Locate the adjustment buttons situated on the left side of the aluminum housing. To cycle through the internal reticle patterns, press and hold the minus button continuously for approximately three to five seconds. Watch the projected reticle pattern on the glass until it changes or flashes, which indicates that the optic's internal logic board has accepted the command to switch patterns.
Step 3: Cycle and Select the Desired Reticle Pattern
With the programming mode active, briefly press the minus button once for each pattern change until your preferred reticle configuration appears on the glass. The EPS Carry Multi-Reticle System typically sequences through three distinct patterns: the standalone 2 MOA precision aiming dot, the combined 32 MOA circle with the center 2 MOA dot, and the standalone 32 MOA ring.
Step 4: Save and Lock Your Reticle Selection
Once your preferred reticle is displayed on the screen, save the setting by pressing and holding the plus button for three seconds, or simply wait approximately five seconds for the optic to automatically time out and exit programming mode. The EPS Carry will store this selection in its non-volatile memory, ensuring your chosen reticle remains active even if the battery is removed or replaced.
Pro-Tip: If you suffer from astigmatism, experiment with the standalone 2 MOA dot versus the 32 MOA circle; many shooters experience less starbursting or distortion with the large outer ring due to how the human eye focuses on larger geometric shapes.
Holosun EPS Carry Review | Outdoor Life
EPS Carry Technical Specifications & Reticle Matrix
| Reticle Configuration | Subtention Size | Primary Application | Battery Impact |
|---|---|---|---|
| 2 MOA Dot Only | 2 Inches at 100 Yards | Precision target engagement, long-range accuracy | Lowest power consumption |
| 32 MOA Circle & Dot | 32 Inch Ring / 2 Inch Dot | Rapid target acquisition, close-quarters combat | Moderate power consumption |
| 32 MOA Circle Only | 32 Inches at 100 Yards | Shotgun-style pointing, dynamic movement tracking | Moderate power consumption |
Common Operational Failures & Field Fixes
- Root Cause: The reticle fails to change or the buttons are unresponsive due to carbon buildup or moisture trapped inside the rubber button membrane.
- Actionable Fix: Clean the exterior housing and buttons with an isopropyl alcohol swab and compressed air to clear debris obstructing the micro-switch travel.
- Root Cause: The reticle appears extremely dim, blurry, or washed out when attempting to change patterns.
- Actionable Fix: Replace the side-tray CR1632 battery with a fresh lithium cell, as low voltage causes erratic LED emitter output and logic processor freezes.
- Root Cause: The reticle changes randomly or the optic resets its brightness settings during live-fire recoil.
- Actionable Fix: Remove the battery tray, inspect the internal spring contacts for corrosion, and ensure the tray screw is fully torqued down to maintain a stable electrical circuit.
Frequently Asked Questions
Can I change the reticle color on my Holosun EPS Carry?
No, the reticle color is determined by the physical LED emitter installed at the factory during production. You must choose between the red emitter model or the green emitter model at the time of purchase, as the internal hardware cannot switch colors dynamically.
Does changing the reticle affect my zero?
No, changing the reticle patterns within the multi-reticle system does not shift your point of impact or require re-zeroing. The center 2 MOA dot shares the exact same mechanical center as the reference point for the 32 MOA circle configurations.
Why won't my EPS Carry enter reticle programming mode?
If holding the minus button for five seconds does not change the reticle, the optic may be locked in lockout mode or running depleted battery voltage. Check the manual for lockout override sequences or replace the battery immediately.
Will the EPS Carry remember my reticle choice after a battery change?
Yes, the optic utilizes non-volatile flash memory to store your last active reticle pattern and brightness level. Removing the side battery tray to replace the cell will not wipe your customized settings.
Calibrate your Holosun EPS Carry reticle to match your exact defensive requirements and verify your zero at the range today.
